T91 80% Lower Receiver, T91 Front Sight Assembly for Wolf A1 Upper Now Available!

[e292644]

T91 80% Lower Receiver,
T91 Front Sight Assembly for Wolf A1 Upper Now Available!
Please visit our STORE for details.

T91LR1-1.jpg

T91LR3.jpg

T91LR4.jpg

T91FSA.jpg

T91FSA1.jpg

[shaocaholica]

80% lower is dope. Are you able to get the font used for the serial number? If not, a high res '0123456789' reference image and I can vectorize it for laser engravers out there.

It looks like the font has changed a little from some of the images I've found online. I kind of like the older font but its a minor difference.

[changhsu08]

The front sight assembly will fit all 3 wolf A1 uppers (the 16, 14.5 and 12)?

[e292644]

Yes, it's 18mm in specs and should fit all Wolf A1 uppers barrel.

The front sight assembly will fit all 3 wolf A1 uppers (the 16, 14.5 and 12)?

[JTM20]

Yes, it's 18mm in specs and should fit all Wolf A1 uppers barrel.

The front sight assembly will fit all 3 wolf A1 uppers (the 16, 14.5 and 12)?

Do the gas hole and pin need to be redrilled to swap the sights?

[e292644]

Yes, new gas block has pilots pre-drilled. For proper fitting it need to be installed and aligned with center then drill through. Gunsmith recommend.

Do the gas hole and pin need to be redrilled to swap the sights?

[JTM20]

Yes, new gas block has pilots pre-drilled. For proper fitting it need to be installed and aligned with center then drill through. Gunsmith recommend.

Do the gas hole and pin need to be redrilled to swap the sights?

Thanks.

I also would like the serial number font if it's available. I want to pick up a receiver but I'd also like it to have a serial number with the correct font.

[e292644]

We are working on getting the correct font list here.
Stay tuned.

[codyphillips48]

Just received my 80% from the t91 store. it looks great need to get some numbers on it to look the part.

[e292644]

This is the most matched one I can get for now.

font.jpg

Titillium.zip

[changhsu08]

Any recommendation to completely remove the Wolf A1 gas block? I got the pin removed but the A1 gas block is not moving at all.
My gun smith hates it.

[akguy1985]

Any recommendation to completely remove the Wolf A1 gas block? I got the pin removed but the A1 gas block is not moving at all.
My gun smith hates it.

Will probably need taken off with a press.

[WelchyV90]

How deep are the engravings on the 80% lower? Is the material prepped for anodizing (sand blasted) ? I had one lowers engravings be destroyed by someone sandblasting for prep for anodizing

[shaocaholica]

How deep are the engravings on the 80% lower? Is the material prepped for anodizing (sand blasted) ? I had one lowers engravings be destroyed by someone sandblasting for prep for anodizing

Are you going to add your own serial number to match the original factory serial number? You’ll probably want to blast after doing that work. Ideally you would blast it after machining and deburring. The engravings looks pretty deep from the photos.

[WelchyV90]

How deep are the engravings on the 80% lower? Is the material prepped for anodizing (sand blasted) ? I had one lowers engravings be destroyed by someone sandblasting for prep for anodizing

Are you going to add your own serial number to match the original factory serial number? You’ll probably want to blast after doing that work. Ideally you would blast it after machining and deburring. The engravings looks pretty deep from the photos.

I am not adding serial numbers cause they are not needed. I just wanted to make sure on the engravings cause the last one was blasted with 100 grit all around and it destroyed the characters.