I currently have the M-Lok handguard on my Wolf A1 12.5in. upper and I'm not happy about the slight wobble on the front-end of the handguard pins.
T-91 Quad Rail
Moderators: e292644, blueeyedwolf
-
JAO1988
- I
- Posts: 1
- Joined: Mon Apr 22, 2019 5:32 pm
- Country: USA
- Location: Florida
I've heard there was going to be a listing for Quad Rails available again for the T-91. Anyone have information on when they will be released?
I currently have the M-Lok handguard on my Wolf A1 12.5in. upper and I'm not happy about the slight wobble on the front-end of the handguard pins.
I currently have the M-Lok handguard on my Wolf A1 12.5in. upper and I'm not happy about the slight wobble on the front-end of the handguard pins.
-
Gherkin Warrior
- II
- Posts: 7
- Joined: Tue Aug 11, 2020 8:22 am
- Country: USA
- Location: Michigan
Found this, haven't purchased yet. Curious if anyone has ever bought anything from Taiwan.
http://www.bbdragon.com.tw/product_info ... ts_id/3008
http://www.bbdragon.com.tw/product_info ... ts_id/3008
-
e292644
- Site Admin
- Posts: 453
- Joined: Thu Apr 20, 2017 5:47 pm
- Country: USA
- Location: AZ
- Contact:
How can I help?
-
Gherkin Warrior
- II
- Posts: 7
- Joined: Tue Aug 11, 2020 8:22 am
- Country: USA
- Location: Michigan
So I ended up pulling the trigger on buying the airsoft quad rail from Taiwan, was 92.50 + 12 shipping. I'll post pics when it arrives. Until then I found this as well as another option. That came today and have to go to my gunsmith and see how it fits as I am getting a J-comp put on it.
https://botach.com/ergo-universal-picatinny-rails/
https://botach.com/ergo-universal-picatinny-rails/
-
Gherkin Warrior
- II
- Posts: 7
- Joined: Tue Aug 11, 2020 8:22 am
- Country: USA
- Location: Michigan
So it finally arrived today, still waiting for my upper to be finished at the gunsmith. Initial impressions are that it feels very well made, solid. I will have to remove thw the takedown pin from the original one as this doesn't come with. Until then ta dah.
You do not have the required permissions to view the files attached to this post.
-
Gherkin Warrior
- II
- Posts: 7
- Joined: Tue Aug 11, 2020 8:22 am
- Country: USA
- Location: Michigan
Here you go 
You do not have the required permissions to view the files attached to this post.
-
Gherkin Warrior
- II
- Posts: 7
- Joined: Tue Aug 11, 2020 8:22 am
- Country: USA
- Location: Michigan
Ok, so here's the skinny so far. It is going to need something to hold it together as it doesn't have the same kind of detent spring as the stock handguard. I suspect something like the one used on the other handguards listed here with the 2 cotter keys to hold it in place. If I figure out a more solid work around I will post. Until then not going to be able to install it.
-
e292644
- Site Admin
- Posts: 453
- Joined: Thu Apr 20, 2017 5:47 pm
- Country: USA
- Location: AZ
- Contact:
-
Gherkin Warrior
- II
- Posts: 7
- Joined: Tue Aug 11, 2020 8:22 am
- Country: USA
- Location: Michigan
Another issue I have run into is the lower guard does not fit into the retainer as it is too thick at this spot and will need to be either milled/filed/sanded down a little bit, looks like about 2mm might do the job, can't go too thin here as the rail here is not very thick.